Step-by-Step Guide to Using a BOD Analyzer

How to use a BOD analyzer? This is a common question for first-time users. With the advancement of technology, the emergence of BOD analyzers has brought great convenience to environmental monitoring, enabling the rapid determination of Biochemical Oxygen Demand (BOD) in water samples. Below is a guide on how to operate a BOD analyzer and key precautions to follow.
Part 1: Operating the BOD Analyzer
I. Preparing the Electrolytic Cell
a. Inject about 2 mL of saturated (K2SO4) solution into the inner filling chamber of the cleaned tungsten rod (indicating negative electrode). Ensure the liquid level is approximately 70 mm above the bottom of the electrode's quartz sand core.
b. Inject about 2 mL of 3mol/L sulfuric acid solution into the inner filling chamber of the single platinum wire (electrolytic anode).
c. Let the electrolytic cell stand for 10 minutes. Check for any noticeable leakage of the filling liquids and replenish them before the experiment if necessary.
d. Place the electrolytic cell onto the stirrer located on the right side of the main unit.
e. Connect the red clip of the electrolysis wire to the lead terminal of the single platinum wire (electrolytic anode).
f. Connect the black clip of the electrolysis wire to the lead terminal of the double platinum plates (electrolytic cathode).
g. Connect the red clip of the signal wire to the lead terminal of the single platinum plate (indicating positive electrode).
h. Connect the black clip of the signal wire to the lead terminal of the tungsten rod (indicating negative electrode).
i. Plug the electrolysis wire and signal wire into their corresponding ports on the back panel of the main unit.
II. Measurement Procedure
a. Add 45 mL of distilled water and 17 mL of concentrated sulfuric acid into a clean digestion cup. Allow it to cool, then add 7 mL of ferric sulfate solution, 1.0 mL of K2Cr2O7 solution, and a magnetic stir bar.
b. Place the digestion cup into the recessed slot of the stirrer, and connect the electrodes following the instructions in the "Preparing the Electrolytic Cell" section.
c. Turn on the power. Adjust the stirrer potentiometer to select an appropriate stirring speed (the electrolyte should swirl smoothly without generating air bubbles).
d. Press the "Blank/Sample" button to set the instrument to Blank mode, and select an electrolysis current of "20mA".
e. Press the "Start" key. After the instrument completes automatic potential compensation, the electrolysis indicator light will turn on. The instrument will begin electrolysis and plot a signal-time graph. Once the endpoint is reached, the buzzer will sound, the electrolysis current will automatically cut off, and the COD/BOD value will be displayed.
f. Discard the first set of data. Add another 1 mL of K2Cr2O7 standard solution into the same digestion cup to perform another measurement. Repeat this step 3 to 4 times. If the repeatability error is within ±2% and the average reading is around "40", it indicates that the instrument is operating normally, and its accuracy and reproducibility meet the technical requirements.
Part 2: Precautions & Best Practices
Thoroughly clean glassware: Soak and wash glassware with detergent first, then soak in dilute hydrochloric acid, and finally rinse thoroughly in sequence with tap water and distilled water.
Avoid air bubbles: When using siphons or pipettes to transfer water samples, chemical reagents, or dilution water, keep the tip of the tube completely submerged below the liquid surface to prevent air bubbles, which can skew the accuracy of the measurement.
Control dilution water quality: The BOD5 of the seeded dilution water must be 0.3~1.0 mg/L. It should be used immediately after preparation.
Monitor oxygen consumption: The 5-day oxygen depletion of the seeded diluted water sample should be greater than 2 mg/L, and the residual dissolved oxygen after the 5-day incubation must be greater than 1 mg/L. Ideally, the dissolved oxygen consumed over the 5 days should account for 40% to 70% of the initial dissolved oxygen.
Shen ChangHong
